🏖️ How Much Microplastic Is in Our Sand?

Collect sand samples from different spots (wet shoreline, high-tide line, playground or riverbank), separate plastic using a salt-water density test, and count pieces under a magnifier. Real citizen-science groups use a similar method.

Free · US Letter · no sign-up
Google Classroom Save to Pinterest Email me
🎒 8th grade🎒 High school♻️ Environment📶 Challenging⏱️ 1–2 weeks💲 Under $10🧑‍🔬 Grown-up helps

Question: Which location has the most microplastic pieces per cup of sand?

Hypothesis: If sand is collected at the high-tide (wrack) line, then it will contain the most microplastics, because floating debris is left there when the water goes back out.

Variables

  • Independent variable (what you change): Sampling location
  • Dependent variable (what you measure): Number of plastic pieces (1–5 mm) per 1 cup (240 mL) of dry sand
  • Controlled variables (keep the same): Same sample volume and depth (top 1 inch / 2.5 cm); Same salt solution; Same counting method and magnifier; Same time per sample

Materials

  • Metal spoon and measuring cup
  • Glass jars with lids (labeled)
  • Table salt and warm water (saturated salt solution)
  • Fine kitchen sieve or coffee filters
  • Magnifying glass or phone macro lens
  • Tweezers
  • White paper plates
  • Gloves

Procedure — step by step

  1. At each location, collect 3 samples of the top 1 inch of sand, 1 cup each, at least 10 feet (3 m) apart.
  2. Spread samples on paper plates to dry for 2 days.
  3. Make a saturated salt solution: stir salt into warm water until no more dissolves.
  4. Put 1 cup of dry sand in a jar with 2 cups of salt solution, shake for 1 minute, and let settle for 10 minutes.
  5. Pour off the floating material through a coffee filter.
  6. Under a magnifier, use tweezers to sort pieces onto a white plate: fragments, fibers, foam, pellets.
  7. Test suspicious pieces with a hot needle (adult only): plastic melts or curls; sand and shell do not.
  8. Count pieces per sample and average each location.

⚠️ Safety: Wear gloves when collecting, and an adult should handle any hot needle. Only collect where it is allowed.

Data table

Microplastic pieces per cup of sand
LocationSample 1Sample 2Sample 3AverageMost common type
Shoreline (wet)     
High-tide line     
Dune / back beach     
Playground or riverbank     

Graph it as a bar graph: put “Location” on the x-axis and your measurement on the y-axis.

Printable project sheets

A plan with every step, and a data sheet with a graph grid and conclusion lines.

Project plan

🏖️ How Much Microplastic Is in Our Sand?

Name:Due:

Question: Which location has the most microplastic pieces per cup of sand?

My hypothesis: If sand is collected at the high-tide (wrack) line, then it will contain the most microplastics, because floating debris is left there when the water goes back out.

Change: Sampling location · Measure: Number of plastic pieces (1–5 mm) per 1 cup (240 mL) of dry sand · Keep the same: Same sample volume and depth (top 1 inch / 2.5 cm); Same salt solution; Same counting method and magnifier; Same time per sample

Materials

  • Metal spoon and measuring cup
  • Glass jars with lids (labeled)
  • Table salt and warm water (saturated salt solution)
  • Fine kitchen sieve or coffee filters
  • Magnifying glass or phone macro lens
  • Tweezers
  • White paper plates
  • Gloves

Steps (check them off)

  1. ☐ At each location, collect 3 samples of the top 1 inch of sand, 1 cup each, at least 10 feet (3 m) apart.
  2. ☐ Spread samples on paper plates to dry for 2 days.
  3. ☐ Make a saturated salt solution: stir salt into warm water until no more dissolves.
  4. ☐ Put 1 cup of dry sand in a jar with 2 cups of salt solution, shake for 1 minute, and let settle for 10 minutes.
  5. ☐ Pour off the floating material through a coffee filter.
  6. ☐ Under a magnifier, use tweezers to sort pieces onto a white plate: fragments, fibers, foam, pellets.
  7. ☐ Test suspicious pieces with a hot needle (adult only): plastic melts or curls; sand and shell do not.
  8. ☐ Count pieces per sample and average each location.

Safety: Wear gloves when collecting, and an adult should handle any hot needle. Only collect where it is allowed.

thinkabara.com/science/science-fair-projects/microplastics-in-beach-sand

Data sheet + graph

Data: Microplastic pieces per cup of sand

LocationSample 1Sample 2Sample 3AverageMost common type
Shoreline (wet)
High-tide line
Dune / back beach
Playground or riverbank

My bar graph (x: Location)

Conclusion: Was my hypothesis supported? What did I learn?

thinkabara.com/science/science-fair-projects/microplastics-in-beach-sand

What usually happens

Counts vary a lot by beach. The high-tide line often has the most pieces, and fragments and foam are usually the most common types. Some samples may have zero, which is also a valid result.

The science behind it

Microplastics are plastic pieces smaller than 5 mm. They come from larger items breaking down in sunlight and waves, from synthetic clothing fibers, and from foam. Most common plastics are less dense than saturated salt water (about 1.2 g/cm³), so they float while sand grains (about 2.6 g/cm³) sink — density separation. Microplastics can be eaten by small animals and enter food webs.

Take it further

  • Compare samples after a storm with calm weeks.
  • Share your data with a citizen-science microplastic survey.
  • Test whether a fiber filter on a washing machine drain catches fibers.

Putting it on your board

Left panel: question, hypothesis and variables. Center: your title, graph and photos of the setup. Right panel: procedure summary, results and conclusion. See the scientific method guide for a printable board layout and judging checklist, or browse more 8th grade projects.

Frequently asked questions

Is “How Much Microplastic Is in Our Sand” a good science fair project for grades 8–hs?

Yes. It is rated challenging, takes 1–2 weeks, costs under about $10 and has a real measurable result, which is what judges look for. A grown-up should help with some steps.

What is the independent variable in this project?

Sampling location. The dependent variable (what you measure) is: number of plastic pieces (1–5 mm) per 1 cup (240 mL) of dry sand.

What results should I expect?

Counts vary a lot by beach. The high-tide line often has the most pieces, and fragments and foam are usually the most common types. Some samples may have zero, which is also a valid result.

How many trials should I do?

At least three for every condition, then average them. More trials make your conclusion stronger, and if one trial is very different, you can explain why (and maybe redo it).

More free printables from Thinkabara