🌉 Which Bridge Design Holds the Most Weight?

Build beam, Warren truss and Pratt truss bridges from the same number of craft sticks and load them until they fail. You compare strength-to-weight ratios like real engineers.

Free · US Letter · no sign-up
Google Classroom Save to Pinterest Email me
🎒 7th grade🎒 8th grade🛠️ Engineering📶 Medium⏱️ 1–2 weeks💲 Under $10

Question: Which bridge design holds the most weight for the same amount of material?

Hypothesis: If a bridge uses a triangle-based truss, then it will hold more weight, because triangles spread the load and do not change shape under force.

Variables

  • Independent variable (what you change): Bridge design (flat beam, Warren truss, Pratt truss)
  • Dependent variable (what you measure): Load at failure (pounds/kg) and strength-to-weight ratio
  • Controlled variables (keep the same): Same number of sticks (60) and same glue; Same span: 12 inches (30 cm); Same drying time (24 h); Same loading method

Materials

  • About 600 jumbo craft sticks
  • Wood glue
  • Clothespins to clamp
  • Two chairs or tables set 12 inches apart
  • Bucket with a handle and a rope or S-hook
  • Sand or water and a bathroom/kitchen scale
  • Safety goggles

Procedure — step by step

  1. Draw each design to scale on paper: a flat laminated beam, a Warren truss (equal triangles), and a Pratt truss (verticals with diagonals sloping toward the center).
  2. Build 3 bridges of each design using exactly 60 sticks each, gluing over your drawing.
  3. Clamp joints and let each bridge dry for 24 hours.
  4. Weigh each bridge.
  5. Set a bridge across the 12-inch gap and hang the bucket from the center.
  6. Add sand slowly, a cup at a time, until the bridge breaks.
  7. Weigh the bucket and sand to get the failure load, and note where it broke.
  8. Calculate strength-to-weight ratio = failure load ÷ bridge weight.

⚠️ Safety: Wear goggles — sticks can snap and fly. Keep feet clear of the bucket.

Data table

Bridge test results
DesignBridge weightFailure load T1T2T3Avg loadStrength ÷ weight
Flat beam      
Warren truss      
Pratt truss      

Graph it as a bar graph: put “Design” on the x-axis and your measurement on the y-axis.

Printable project sheets

A plan with every step, and a data sheet with a graph grid and conclusion lines.

Project plan

🌉 Which Bridge Design Holds the Most Weight?

Name:Due:

Question: Which bridge design holds the most weight for the same amount of material?

My hypothesis: If a bridge uses a triangle-based truss, then it will hold more weight, because triangles spread the load and do not change shape under force.

Change: Bridge design (flat beam, Warren truss, Pratt truss) · Measure: Load at failure (pounds/kg) and strength-to-weight ratio · Keep the same: Same number of sticks (60) and same glue; Same span: 12 inches (30 cm); Same drying time (24 h); Same loading method

Materials

  • About 600 jumbo craft sticks
  • Wood glue
  • Clothespins to clamp
  • Two chairs or tables set 12 inches apart
  • Bucket with a handle and a rope or S-hook
  • Sand or water and a bathroom/kitchen scale
  • Safety goggles

Steps (check them off)

  1. ☐ Draw each design to scale on paper: a flat laminated beam, a Warren truss (equal triangles), and a Pratt truss (verticals with diagonals sloping toward the center).
  2. ☐ Build 3 bridges of each design using exactly 60 sticks each, gluing over your drawing.
  3. ☐ Clamp joints and let each bridge dry for 24 hours.
  4. ☐ Weigh each bridge.
  5. ☐ Set a bridge across the 12-inch gap and hang the bucket from the center.
  6. ☐ Add sand slowly, a cup at a time, until the bridge breaks.
  7. ☐ Weigh the bucket and sand to get the failure load, and note where it broke.
  8. ☐ Calculate strength-to-weight ratio = failure load ÷ bridge weight.

Safety: Wear goggles — sticks can snap and fly. Keep feet clear of the bucket.

thinkabara.com/science/science-fair-projects/popsicle-stick-bridge-design

Data sheet + graph

Data: Bridge test results

DesignBridge weightFailure load T1T2T3Avg loadStrength ÷ weight
Flat beam
Warren truss
Pratt truss

My bar graph (x: Design)

Conclusion: Was my hypothesis supported? What did I learn?

thinkabara.com/science/science-fair-projects/popsicle-stick-bridge-design

What usually happens

Truss bridges usually hold far more than the flat beam for the same sticks — often several times more. Most failures happen at glue joints, so careful gluing changes results a lot.

The science behind it

When a bridge carries a load, some parts are squeezed (compression) and others are stretched (tension). A triangle is a rigid shape: its angles cannot change unless a side breaks, so trusses turn bending into tension and compression along each stick, where wood is strong. Engineers judge designs by strength-to-weight ratio because lighter bridges cost less and carry less of their own weight.

Take it further

  • Test where the load is placed: center vs. quarter span.
  • Try an arch design.
  • Add gusset plates at joints and measure the improvement.

Putting it on your board

Left panel: question, hypothesis and variables. Center: your title, graph and photos of the setup. Right panel: procedure summary, results and conclusion. See the scientific method guide for a printable board layout and judging checklist, or browse more 7th grade projects.

Frequently asked questions

Is “Which Bridge Design Holds the Most Weight” a good science fair project for grades 7–8?

Yes. It is rated medium, takes 1–2 weeks, costs under about $10 and has a real measurable result, which is what judges look for.

What is the independent variable in this project?

Bridge design (flat beam, Warren truss, Pratt truss). The dependent variable (what you measure) is: load at failure (pounds/kg) and strength-to-weight ratio.

What results should I expect?

Truss bridges usually hold far more than the flat beam for the same sticks — often several times more. Most failures happen at glue joints, so careful gluing changes results a lot.

How many trials should I do?

At least three for every condition, then average them. More trials make your conclusion stronger, and if one trial is very different, you can explain why (and maybe redo it).

More free printables from Thinkabara